[Dec 14, 2021] Latest CCNP Enterprise 300-410 Actual Free Exam Questions
CCNP Enterprise 300-410 Dumps Updated Practice Test and 215 unique questions
Knowledge Prerequisites
It is good to know what knowledge is required for any exam that you are planning to take. Therefore, you have to find out what it takes to sit for this particular test. Highlighted below are the skills and knowledge required for the Cisco 300-410 exam:
- General understanding of how to effectively secure networks devices;
- General understanding of network fundamentals.
- Knowledge of how to implement LANs;
- Basic knowledge of network automation;
- Understanding and knowledge of how to manage network devices;
All in all, there will be topics that cover infrastructure services and security, VPN technologies, and Layer 3.
NEW QUESTION 84
A network administrator is tasked to permit http and https traffic only toward the internet from the User1 laptop to adhere to company's security policy. The administrator can still ping to www.cisco.com Which interface should the access list 101 be applied to resolve this issue?
- A. Interface G0/48 in the incoming direction
- B. Interface G0/0 in the outgoing direction.
- C. Interface G0/0 in the incoming direction.
- D. Interface S1/0 in the outgoing direction.
Answer: C
NEW QUESTION 85
Refer to the exhibit.
After applying IPsec, the engineer observed that the DMVPN tunnel went down, and both spoke-to-spoke and hub were not establishing. Which two actions resolve the issue? (Choose two.)
- A. Configure the crypto isakmp key cisco address 192.1.1.1 on R2 and R3.
- B. Remove the crypto isakmp key cisco address 10.1.1.1 on R2 and R3.
- C. Change the mode from mode transport to mode tunnel on R2.
- D. Change the mode from mode tunnel to mode transport on R3.
- E. Configure the crypto isakmp key cisco address 0.0.0.0 on R2 and R3.
Answer: D,E
NEW QUESTION 86
Refer to the exhibit.
During troubleshooting it was discovered that the device is not reachable using a secure web browser. What is needed to fix the problem?
- A. permit tcp port 443
- B. permit udp port 465
- C. permit tcp port 22
- D. permit tcp port 465
Answer: A
NEW QUESTION 87
Drag and Drop Question
Drag and drop the DHCP messages from the left onto the correct uses on the right.
Answer:
Explanation:
NEW QUESTION 88 
Refer to the exhibit. A network administrator is troubleshooting OSPF adjacency issue by going through the console logs in the router, but due to an overwhelming log messages stream, it is impossible to capture the problem.
Which two commands reduce console log messages to relevant OSPF neighbor problem details so that the issue can be resolved? (Choose two.)
- A. debug condition interface
- B. debug condition ospf neighbor
- C. debug condition all
- D. debug condition session-id ADJCHG
Answer: A,B
Explanation:
Section: Mixed Questions
NEW QUESTION 89
Refer to the exhibit.
The network administrator configured VRF lite for customer A. The technician at the remote site misconfigured VRF on the router. Which configuration will resolve connectivity for both sites of customer a?
- A. Option D
- B. Option B
- C. Option A
- D. Option C
Answer: A
NEW QUESTION 90
Exhibit:
BGP is flapping after the Copp policy is applied. What are the two solutions to fix the issue?
(Choose two)
- A. Configure IP CEF to CoPP policy and BGP to work
- B. Configure a higher value for CIR under the class COPP-CRITICAL-7600
- C. Configure BGP in the COPP-CRITICAL-7600 ACL
- D. Configure a higher value for CIR under the default class to allow more packets during peak traffic
- E. Configure a three-color policer instead of two-color policer under class COPP-CRITICAL-
7600
Answer: C,D
Explanation:
Explanation
The policy-map COPP-7600 only rate-limit HTTP & HTTPS traffic (based on the ACL conditions) so any BGP packets will be processed in the class "class-default", which drops exceeded BGP packets. Therefore we have two ways to solve this problem:
+ Add BGP to the ACL with the statement "permit tcp any any eq bgp"
+ Configure higher value for CIR in default class as 2Mbps is too low for web traffic (http &
https)
NEW QUESTION 91
Refer to the exhibit.
Which subnet is redistributed from EIGRP to OSPF routing protocols?
- A. 10.2.2.0/24
- B. 10.2.3.0/26
- C. 10.1.2.0/24
- D. 10.1.4.0/26
Answer: A
NEW QUESTION 92
Which configuration enables the VRF that is labeled ''inet'' on FastEthernet0/0?
A)
B)
C)
D)
- A. option D
- B. Option A
- C. option B
- D. Option C
Answer: A
NEW QUESTION 93
Refer to the exhibit.
A router receiving BGP routing updates from multiple neighbors for routers in AS 690. What is the reason that the router still sends traffic that is destined to AS 690 to a neighbor other than 10.222.1.1?
- A. The route map is applied in the wrong direction.
- B. The weight value in another neighbor statement is higher than 200.
- C. The local preference value in another neighbor statement is higher than 250.
- D. The local preference value should be set to the same value as the weight in the route map.
Answer: A
NEW QUESTION 94
When configuring Control Plane Policing on a router to protect it from malicious traffic, an engineer observes that the configured routing protocols start flapping on that device. Which action in the Control Plane Policy prevents this problem in a production environment while achieving the security objective?
- A. Set the conform-action to transmit and exceed-action to drop to test the ACLs and transmit rates and apply the Control Plane Policy m the input direction
- B. Set the conform-action and exceed-action to transmit initially to test the ACLs and transmit rates and apply the Control Plane Policy in the output direction
- C. Set the conform-action to transmit and exceed-action to drop to test the ACLs and transmit rates and apply the Control Plane Policy m the output direction
- D. Set the conform-action and exceed-action to transmit initially to test the ACLs and transmit rates and apply the Control Plane Policy in the input direction
Answer: D
NEW QUESTION 95
Refer to the exhibit.
Which configuration configures a policy on R1 to forward any traffic that is sourced from the
192.168.130.0/24 network to .
A)
B)
C)
D)
- A. Option D
- B. Option B
- C. Option A
- D. Option C
Answer: C
NEW QUESTION 96
Refer to the exhibit.
An engineer is trying to redistribute OSPF to BGP, but not all of the routes are redistributed. What is the reason for this issue?
- A. By default, only internal OSPF routes are redistributed into BGP
- B. Only classful networks are redistributed from OSPF to BGP
- C. By default, only internal routes and external type 1 routes are redistributed into BGP
- D. BGP convergence is slow, so the route will eventually be present in the BGP table
Answer: A
Explanation:
Explanation
If you configure the redistribution of OSPF into BGP without keywords, only OSPF intra-area and inter-area routes are redistributed into BGP, by default.
You can redistribute both internal and external (type-1 & type-2) OSPF routes via this command:
Router(config-router)#redistribute ospf 1 match internal external 1 external 2
NEW QUESTION 97
When provisioning a device in Cisco DNA Center, the engineer sees the error message "Cannot select the device. Not compatible with template".
What is the reason for the error?
- A. The changes to the template were not committed.
- B. The software version of the template is different from the software version of the device.
- C. The tag that was used to filter the templates does not match the device tag.
- D. The template has an incorrect configuration.
Answer: B
NEW QUESTION 98
Drag and drop the MPLS VPN concepts from the left onto the correct descriptions on the right.
Answer:
Explanation:
Reference:
https://www.rogerperkin.co.uk/featured/route-distinguisher-vs-route-target/
NEW QUESTION 99
Refer to the exhibit.
An engineer is trying to generate a summary route in OSPF for network 10.0.0.0/8, but the summary route does not show up in the routing table. Why is the summary route missing?
- A. The summary route is visible only in the OSPF database, not in the routing table.
- B. There is no route for a subnet inside 10.0.0.0/8, so the summary route is not generated.
- C. The summary-address command is used only for summarizing prefixes between areas.
- D. The summary route is not visible on this router, but it is visible on other OSPF routers in the same area.
Answer: C
NEW QUESTION 100
Refer to the exhibit.
PC-2 failed to establish a Telnet connection to the terminal server Which configuration resolves the issue?
- A. Option D
- B. Option B
- C. Option A
- D. Option C
Answer: A
NEW QUESTION 101
Which command is used to check IP SLA when an interface is suspected to receive lots of traffic with options?
- A. show timer
- B. show track
- C. show threshold
- D. show delay
Answer: B
NEW QUESTION 102
When determining if a system is capable of support, what is the minimum time spacing required for a BFD control packet to receive once a control packet is arrived?
- A. Required Min RX Interval
- B. Required Min Echo RX Interval
- C. Detect Mult
- D. Desired Min TX Interval
Answer: A
NEW QUESTION 103
......
Verified 300-410 dumps Q&As - 100% Pass from DumpsKing: https://www.dumpsking.com/300-410-testking-dumps.html
Latest 100% Exam Passing Ratio - 300-410 Dumps PDF: https://drive.google.com/open?id=1tLqQ21lhX2AK8IC-kbYOn7j1w0IKAPVi
