[Q191-Q214] Updated Mar-2026 Test Engine to Practice Test for API-1169 Exam Questions and Answers!

Updated Mar-2026 Test Engine to Practice Test for API-1169 Exam Questions and Answers!

Pipeline Construction Inspector Exam Certification Sample Questions and Practice Exam

NEW QUESTION # 191
How shall tensile strength be computed?
-max load at failure x smallest cross-sect area
-Max load at failure / "
-Min load at failure x largest cross sect area
"/"

• A. The entire weld must be cut out.
• B. Tensile-strength specimens shall be subject to the nick-break test
• C. Atmosphere supplying, air purifying and self contained aparatus
• D. Divide the max load at failure with the smallest cross sectional area of the specimen

Answer: B

NEW QUESTION # 192
Define validation in terms related related to data, information and document.

• A. Confirmation, through the provisions of objective evidence, that the requirements for a specific intended use or application have been fulfilled.(The objective evidence needed for a validation is the result of a test or other form of determination such as performing alternative calculations or reviewing documents)(ISO 9000 3.8.13)
• B. Confirmation, through the provisions of objective evidence, that specified requirements have been fulfilled.(The objective evidence needed for a fair if Acacian can be the result of an inspection or of other forms of determination such as performing alternative calculations or reviewing documents)(ISO 9000 3.8.12)
• C. Document stating requirements(example quality manual, quality plan, technical drawing, procedure document, work instruction.)(ISO 9000 3.8.7)
• D. Is the entity that intends to install, operate, maintain a new pipeline that crosses existing pipeline facilities. The Crossing company may designate a third-party or parties to perform the task necessary to accomplish a Crossing but remains responsible for the work performed by such third parties.

Answer: C

NEW QUESTION # 193
Define limits placed on characteristics of materials, products, and services established by the organization to achieve conformity to the manufacturing or service requirements is the definition of?

• A. Acceptance criteria(api spec q1 3.1.1)
• B. Rework(api 1104 3.1.25)
• C. Manufacturing acceptance criteria(API Spec Q1 3.1.15
• D. Strength, spike, and leak (api 1110 4.1.7)

Answer: C

NEW QUESTION # 194
All compressed gas cylinders and tanks should be properly _______________ and ______________ when transported and stored.

• A. Permits and precautions
• B. Effectiveness
• C. Grading
• D. Secured and labeled

Answer: D

NEW QUESTION # 195
What happens if dent includes part of a weld?

• A. Strength pressure test
• B. Impressed current
• C. The entire weld must be cut out.
• D. Superimposed loads

Answer: C

NEW QUESTION # 196
Green

• A. Communication, alarm or signal lines
• B. Sewers and drain lines
• C. Potable water
• D. Proposed excavation

Answer: B

NEW QUESTION # 197
Leveling the pipeline ROW so construction can proceed smoothly

• A. Easement
• B. Pulverizing
• C. Testing
• D. Grading

Answer: A

NEW QUESTION # 198
When should hearing protection be used?

• A. Hearing protection is used when the work environment noise level exceeds 85 dbA over an 8-hour period
• B. Residence within proximity of the facility being tested, state and local enforcement agencies.(CS-S-9 4.5)
• C. Part of quality management focused on fulfilling quality requirements(ISO 9000 3.3.7)
• D. Liquids having a flashpoint below 100°F are Known as class 1 liquids. The most common is gasoline

Answer: A

NEW QUESTION # 199
Perform these before any mechanical ground disturbance

• A. Sweep locate, pot hole, one call
• B. Identifying, documenting and oversee activity
• C. Impressed current
• D. Pressure testing

Answer: A

NEW QUESTION # 200
What type of signs need to be posted during Hydro/Pressure Testing?

• A. Adequacy, completeness and lack of conflict.
• B. Danger - High Pressure, Testing in progress
• C. Strength pressure test
• D. Required reporting

Answer: B

NEW QUESTION # 201
At a minimum, install and maintain temporary sediment barriers
across the entire construction right-of-way at the base of slopes greater than ________percent where the base of the slope is less than ________ feet from a waterbody

• A. 100 ft
• B. 12 / 120
• C. 5 / 50
• D. 10 / 100

Answer: C

NEW QUESTION # 202
A person who operates either machine or automatic welding equipment

• A. Inspector
• B. Design validation
• C. Welding engineer
• D. Welding operator

Answer: D

NEW QUESTION # 203
Work Permits for excavation would be found under what OSHA standard?

• A. Have the longitude a weld as near as practical to the neutral axis of the band(49 CFR 192.313)
• B. OSHA 1926.650 and 1926.651, (29 CFR 1926) safety and health regulations for construction
• C. OSHA 1910.109 and OSHA 1926.900 to 1926.914
• D. Part of quality management focused on fulfilling quality requirements(ISO 9000 3.3.7)

Answer: D

NEW QUESTION # 204
The construction right-of-way width for a project shall not exceed __________ feet or that described in the FERC application unless otherwise modified by a FERC Order. However, in limited, non-wetland areas, this construction right-ofway width may be expanded by up to __________ feet without Director approval to accommodate full construction right-of-way topsoil segregation and to ensure safe construction where topographic conditions (e.g., side-slopes) or soil limitations require it. Twenty-five feet of extra construction right-of-way width may also be used in limited, non-wetland or non-forested areas for truck turn-arounds where no reasonable alternative access exists.

• A. 85 / 15
• B. 75 / 25
• C. 95 / 5
• D. 90 / 10

Answer: D

NEW QUESTION # 205
Which section outlines depth of cover for transmission lines?

• A. Subpart G 96.327
• B. 100%192.243
• C. Subpart G 192.327
• D. 100%

Answer: D

NEW QUESTION # 206
When there is a possibility of hazardous exposure to radiant energy, how far back must the head area be protected?

• A. Permits and precautions
• B. containment and secondary containment
• C. A vertical line in the back of the ears
• D. radiation-protective, semitransparent materials

Answer: C

NEW QUESTION # 207
Trench ratio for soil type A

• A. 3/4:1
• B. 5/1
• C. 1/2:1
• D. 1 1/2:1

Answer: B

NEW QUESTION # 208
List Attached C, drawing illustration Guidelines found in INGAA Foundation

• A. Strength, spike, and leak(API 1110 4.1.7
• B. Residence within proximity of the facility being tested, state and local enforcement agencies.(CS-S-9 4.5)
• C. Within 24 hours of each 0.50 inch of rainfall(FERC Upland 11.B.13)

Answer: C

NEW QUESTION # 209
On Class 1 pipe, What percentage of pipe must be NDT tested?

• A. 100%192.243
• B. 15% except off-shore
• C. 10% except off-shore
• D. 35% except off-shore

Answer: D

NEW QUESTION # 210
Slope (%) Spacing (feet)
5 - 15 ?
>15 - 30 ?
>30 ?

• A. 0
• B. 50 ft
• C. 1
• D. 2

Answer: B

NEW QUESTION # 211
Wrinkle bends are covered in what section?

• A. 0
• B. 100%192.243
• C. Subpart G 192.315
• D. 100%

Answer: C

NEW QUESTION # 212
If there is a possibility of water entering the casing for a transmission line under a railroad then the _________.

• A. Permit
• B. Clearing
• C. Impressed current
• D. Ends must be sealed

Answer: D

NEW QUESTION # 213
On systems where pipe is telescoped by _______, particular care shall be taken to ensure proper placement of pipe.

• A. Ends must be sealed
• B. grade, wall thickness or both
• C. Site Specific test procedure
• D. Valve protective caps

Answer: D

NEW QUESTION # 214
......

Certification dumps API Certification API-1169 guides - 100% valid: https://www.dumpsking.com/API-1169-testking-dumps.html

100% Pass Your API-1169 Pipeline Construction Inspector Exam at First Attempt with DumpsKing: https://drive.google.com/open?id=115FCRbF-XMEaX3BsZNpC5Gcq13j-0YzC