(2024) 500-220 Exam Dumps, Practice Test Questions BUNDLE PACK
Cisco Meraki Solutions Specialist Certification 500-220 Sample Questions Reliable
Individuals who pass the Cisco 500-220 certification exam will have a range of career options available to them. They will be qualified to work as network engineers, system administrators, and support technicians, among other roles. They will also be able to work with a wide range of organizations, including small businesses, enterprises, and service providers, as Cisco Meraki solutions are used across a variety of industries.
Cisco 500-220 exam consists of 60-70 questions, which can be in the form of multiple-choice, drag and drop, or simulation-based questions. 500-220 exam covers a wide range of topics, including network design, security, wireless access points, switches, and routers. To pass the exam, candidates need to have a good understanding of the Cisco Meraki platform, its features and capabilities, and how to troubleshoot common issues.
NEW QUESTION # 41
Refer to the exhibit.
Which design recommendation should be considered?
- A. A 25-percent throughput loss occurs for every hop. Cisco Meraki best practice recommends a 2-hop maximum.
- B. A 50-percent throughput loss occurs for every hop. Cisco Meraki best practice recommends a 1-hop maximum.
- C. A 25-percent throughput loss occurs for every hop. Cisco Meraki best practice recommends a 1-hop maximum.
- D. A 50-percent throughput loss occurs for every hop. Cisco Meraki best practice recommends a 2-hop maximum.
Answer: B
Explanation:
Explanation
https://documentation.meraki.com/MR/Deployment_Guides/Mesh_Deployment_Guide There will be a throughput reduction (~50% reduction) with each "hop" in a mesh. It is recommended that a mesh network be designed for no more than one mesh hop from the gateway to client device.
NEW QUESTION # 42
One thousand concurrent users stream video to their laptops. A 30/70 split between 2.4 GHz and 5 GHz is used.
Based on client count, how many APs (rounded to the nearest whole number) are needed?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION # 43
In an organization that uses the Co-Termination licensing model, which two operations enable licenses to be applied? (Choose two.)
- A. Call Meraki support.
- B. License a network.
- C. Wait for the devices to auto-renew.
- D. Renew the Dashboard license.
- E. License more devices.
Answer: D,E
Explanation:
Explanation
There are two operations in which a license can be applied, License more devices or Renew my dashboard license. This article will compare both operations and describe their behaviors.
https://documentation.meraki.com/General_Administration/Licensing/Meraki_Licensing_-_License_More_Devi These are the two operations that enable licenses to be applied in an organization that uses the Co-Termination licensing model. According to the Meraki Co-Termination Licensing Overview, there are two ways to add licenses to an organization:
Renewing the Dashboard license: This option allows you to extend the co-termination date of your organization by purchasing new licenses for the same or longer term as your existing licenses. You can renew your Dashboard license from the Organization > Configure > License Info page or from the Meraki Dashboard homepage.
Licensing more devices: This option allows you to add new devices to your organization by purchasing new licenses for them. You can license more devices from the Organization > Inventory page or from the Meraki Dashboard homepage.
NEW QUESTION # 44
Which design requirement is met by implementing syslog versus SNMP?
- A. when organization-wide information must be collected
- B. when information such as flows and client connectivity must be gathered
- C. when automation capabilities are needed
- D. when proactive alerts for critical events must be generated
Answer: B
Explanation:
Explanation
Implementing syslog versus SNMP can meet the design requirement of gathering information such as flows and client connectivity. Syslog can collect and report various types of events, such as VPN connectivity, uplink connectivity, DHCP leases, firewall rules, IDS alerts, and security events. Syslog can also provide detailed information about the flows and client connectivity on the network devices, such as source and destination IP addresses, ports, protocols, bytes transferred, etc. SNMP, on the other hand, can collect and report various statistics and information about the network devices, such as CPU utilization, interface status, memory usage, etc. However, SNMP does not provide as much information about the flows and client connectivity as syslog does.
NEW QUESTION # 45
What occurs when a configuration change is made to an MX network that is bound to a configuration template?
- A. The template configuration overrides the configuration change in the bound network.
- B. The configuration change in the bound network overrides the template configuration.
- C. The more restrictive configuration is preferred.
- D. The configuration change in the bound network is combined with the template configuration inside the template.
Answer: B
Explanation:
Explanation
https://documentation.meraki.com/Architectures_and_Best_Practices/Cisco_Meraki_Best_Practice_Design/Best
NEW QUESTION # 46
Refer to the exhibit.
The VPN concentrator is experiencing issues. Which action should be taken to ensure a stable environment?
- A. Configure the MX appliance to Routed mode on the Addressing & VLANS page.
- B. Physically disconnect all LAN ports.
- C. Add a deny any/any firewall rule to the end of the firewall rules.
- D. Remove the connection from Internet 1.
Answer: B
NEW QUESTION # 47
A customer requires a hub-and-spoke Auto VPN deployment with two NAT-mode hubs with dual uplink connections and 50 remote sites with a single uplink connection.
How many tunnels does each hub need to support?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION # 48
Drag and drop the descriptions from the left onto the corresponding MX operation mode on the right.
Answer:
Explanation:
Explanation
Routed Mode:
This mode is the default mode of operation
This mode is generally also the default gateway for devices on the LAN
Client traffic to the internet has the source IP rewritten to match the WAN IP of the appliance DHCP services can be configured on the MX appliance Passthrough Mode:
The MX appliance acts as a layer 2 bridge
VLANs cannot be configured
No address translation is provided
This mode is not recommended at the network perimeter
This question is related to the topic of MX Addressing and VLANs in the Cisco Meraki documentation. You can find more information about this topic in the MX Addressing and VLANs article or the General MX Best Practices page.
NEW QUESTION # 49
Which two primary metrics does Meraki Insight use to calculate the Application Performance Score? (Choose two.)
- A. Total Bandwidth Usage
- B. Maximum Latency
- C. Per-flow Goodput
- D. Application Response Time
- E. Maximum Jitter
Answer: C,D
NEW QUESTION # 50
Refer to the exhibit.
Which two actions are required to optimize load balancing asymmetrically with a 4:1 ratio between links?
(Choose two.)
- A. Set the speed of the cellular uplink to zero.
- B. Change the primary uplink to "none".
- C. Add an internet traffic preference that defines the load-balancing ratio as 4:1.
- D. Change the assigned speeds of WAN 1 and WAN 2 so that the ratio is 4:1.
- E. Enable load balancing.
Answer: D,E
Explanation:
Explanation
To clarify, to optimize load balancing asymmetrically with a 4:1 ratio between links, two actions that are required are:
Enable load balancing: This option allows the MX to use both of its uplinks for load balancing. When load balancing is enabled under Security & SD-WAN > Configure > SD-WAN & Traffic shaping, traffic flows will be distributed between the two uplinks proportional to the WAN 1 and WAN 2 bandwidths specified under Uplink configuration1.
Change the assigned speeds of WAN 1 and WAN 2 so that the ratio is 4:1: The assigned speed of a WAN link is a value that indicates the bandwidth available on that link. By changing the assigned speeds of WAN 1 and WAN 2 so that they reflect the desired load-balancing ratio, the administrator can ensure that the MX uses both links efficiently and proportionally1. For example, if WAN 1 has a bandwidth of 100 Mbps and WAN 2 has a bandwidth of 25 Mbps, then setting their assigned speeds to
100 Mbps and 25 Mbps respectively will achieve a 4:1 load-balancing ratio.
NEW QUESTION # 51
What is a feature of distributed Layer 3 roaming?
- A. An MX Security Appliance is required as a concentrator.
- B. An MX Security Appliance is not required as a concentrator.
- C. All wireless client traffic can be split-tunneled.
- D. All wireless client traffic is tunneled.
Answer: B
Explanation:
Reference:
Cisco_Meraki_Best_Practice_Design/Best_Practice_Design_-_MR_Wireless/
Wireless_Layer_3_Roaming_Best_Practices
NEW QUESTION # 52
Refer to the exhibit.
Which outcome occurs when logging is set to Enabled?
- A. Inbound flows are sent to a configured syslog server if a syslog server configured for flows.
- B. The hits counter within this section is now enabled.
- C. This firewall rule is now enabled.
- D. Outbound flows are sent to a configured syslog server if a syslog sender is configured for flows.
Answer: D
Explanation:
Explanation
"Inbound and outbound flows will generate a syslog message showing the source and destination along with port numbers and the firewall rule that they matched. For inbound rules, 1=deny and 0=allow."
https://documentation.meraki.com/General_Administration/Monitoring_and_Reporting/Syslog_Server_Overview
NEW QUESTION # 53
For which two reasons can an organization become "Out of License"? (Choose two.)
- A. more hardware devices than device licenses
- B. licenses that do not match the serial numbers in the organization
- C. MR licenses that do not match the MR models in the organization
- D. licenses that are in the wrong network
- E. expired device license
Answer: A,E
NEW QUESTION # 54
Drag and drop the descriptions from the left onto the permission types on the right.
Answer:
Explanation:
NEW QUESTION # 55
Refer to the exhibit.
For an AP that displays this alert, which network access control method must be in use?
- A. MAC-based access control with RADIUS server
- B. WPA2-enterprise with my RADIUS server
- C. preshared key
- D. splash page with my RADIUS server
Answer: C
NEW QUESTION # 56
Which API endpoint clones a new Organization?
- A. PUT /organizations/{organizationId}/clone
- B. POST /organizations/{organizationId}/new
- C. POST /organizations/{organizationId}/clone
- D. POST /organizations/clone/{organizationId}
Answer: B
NEW QUESTION # 57
Which design requirement is met by implementing syslog versus SNMP?
- A. when organization-wide information must be collected
- B. when information such as flows and client connectivity must be gathered
- C. when automation capabilities are needed
- D. when proactive alerts for critical events must be generated
Answer: B
Explanation:
Reference:
Meraki_Device_Reporting_-_Syslog%2C_SNMP%2C_and_API
NEW QUESTION # 58
Refer to the exhibit.
What are the Loss and Average Latency statistics based on?
- A. responses that the MX appliance receives on the connectivity-testing IP addresses on the Security & SD- WAN > Firewall page
- B. responses that the MX appliance receives on the connectivity-testing hostnames on the Insight > Web App Health page
- C. responses that the MX appliance receives on the connectivity-testing IP addresses on the Help > Firewall info page
- D. responses that the MX appliance receives on the connectivity-testing IP address that is configured on the Security & SD-WAN > SD-WAN & Traffic Shaping page
Answer: A
NEW QUESTION # 59
Refer to the exhibit.
What is an advantage of implementing inter-VLAN routing on an MX Security Appliance rather than performing inter-VLAN routing on an MS Series Switch?
- A. The MX appliance performs data encryption for inter-VLAN traffic.
- B. The MX appliance performs content filtering for inter-VLAN traffic.
- C. The MX appliance performs AMP for inter-VLAN traffic.
- D. The MX appliance performs IDS/IPS for inter-VLAN traffic.
Answer: A
NEW QUESTION # 60
Which information do the MXs in a High Availability pair share?
- A. DHCP association database
- B. stateful firewall database
- C. spanning-tree state
- D. time synchronization state
Answer: C
NEW QUESTION # 61
Refer to the exhibit.
During a Meraki AP deployment, the default SSID that the exhibit shows is broadcast. What causes this behavior?
- A. An AP cannot connect to the default gateway.
- B. An AP has never connected to the Meraki Cloud Controller.
- C. An AP does not have a wired connection to the network.
- D. An AP has Site Survey mode enabled.
Answer: B
Explanation:
Explanation
If a Meraki Access Point does not have a configuration from the Meraki Cloud Controller it will instead broadcast a default SSID of "Meraki-Scanning." vs <SSID_name>-scanning Cause: Similar to 'bad-gateway', an AP is unable to connect to its default gateway.
https://documentation.meraki.com/MR/Other_Topics/Troubleshooting_local_connection_issues_using_default_S This is because the AP is broadcasting the default SSID "meraki-scanning" which is only broadcast when the AP has never connected to the Meraki Cloud Controller1.
This question is related to the topic of Wireless Access Points Quick Start in the Cisco Meraki documentation.
You can find more information about this topic in the Wireless Access Points Quick Start article or the Using the Cisco Meraki Device Local Status Page page.
NEW QUESTION # 62
What occurs when a configuration change is made to an MX network that is bound to a configuration template?
- A. The template configuration overrides the configuration change in the bound network.
- B. The configuration change in the bound network is combined with the template configuration inside the template.
- C. The more restrictive configuration is preferred.
- D. The configuration change in the bound network overrides the template configuration.
Answer: B
Explanation:
Reference:
Managing_Multiple_Networks_with_Configuration_Templates
NEW QUESTION # 63
An organization requires that BYOD devices be enrolled in Systems Manager before they gain access to the network. Part of the enrollment includes pushing out the corporate SSID preshared key, corporate email settings, and some business-sensitive PDFs. When a user leaves the organization, which Systems Manager feature allows the removal of only the MDM-delivered content from the user's device?
- A. Erase Device
- B. Unenroll Device
- C. Clear Pushed Data
- D. Selective Wipe
Answer: D
Explanation:
Explanation
https://documentation.meraki.com/SM/Monitoring_and_Reporting/Selective_Wipe_and_Device_Quarantine_in_
NEW QUESTION # 64
Which information is used to calculate whether a WAN link has high usage?
- A. total number of devices that are actively passing traffic
- B. value under Security & SD WAN > SD WAN & Traffic Shaping > Uplink Configuration
- C. total historical throughput of an uplink
- D. data under Security & SD WAN > Appliance Status > Uplink > Live Data
Answer: B
Explanation:
Explanation
Which information is used to calculate whether a WAN link has high usage not how to view (To accurately identify high utilization, users must set the ISP-provided bandwidth limits under Security and SD-WAN > SD-WAN and Traffic Shaping > Uplink Configuration for each uplink. If the bandwidth usage is higher than
80% of the defined limit, it will mark that uplink as High Usage.)
https://documentation.meraki.com/MI/MI_WAN_Health#:~:text=To%20accurately%20identify%20high%20util
NEW QUESTION # 65
When wireless SSIDs are configured in Dashboard, which setting on the Access Control page affects the ability of a 2.4 GHz only client device from associating to the WLAN for the first time?
- A. Dual band operating with Band Steering
- B. Content filtering
- C. Bridge mode
- D. 802.11r
Answer: A
Explanation:
Explanation
When band steering is enabled on an SSID, APs will stop advertising that SSID in 2.4GHz beacons. Since
2.4GHz-only clients that rely on a passive scan will not "see" that SSID in beacons, they might not be able to join this SSID unless they do an active scan or have been pre-configured with the SSID name and security settings (for example, a pre-shared key).
https://documentation.meraki.com/MR/Radio_Settings/Band_Steering
NEW QUESTION # 66
......
Prepare for the Actual Cisco Meraki Solutions Specialist 500-220 Exam Practice Materials Collection: https://www.dumpsking.com/500-220-testking-dumps.html
Cisco Meraki Solutions Specialist Certified Official Practice Test 500-220: https://drive.google.com/open?id=1BvAbmNrhajWhpgaJMwdw2FVv0Vph_rKN
